Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Keypad & Intercom Repair: The Winchester Owner’s Guide
Keypad and intercom repair for Ghost Controls gate openers usually runs $185 to $340 installed in Winchester, and most repairs are completed in a single visit. The wireless keypad itself is often the affordable part; the intercom side and any wiring to the house push the price up. Call us at (866) 984-8340 for a free estimate and we’ll price your exact model before anything is ordered.
Owners in Winchester tend to notice this one slowly. The keypad takes two or three presses to open the gate, or the intercom goes from clear to crackly to dead over a summer. Then one morning the gate won’t open from the driveway at all and the only way in is the car remote. That’s the point most people call. We service Ghost Controls alongside LiftMaster, Mighty Mule, DoorKing and six other brands, so we know this equipment.
Which Ghost Controls Models This Applies To
Ghost Controls builds its keypads and intercoms as add-on accessories that work across the AX, AR, and TSS series openers, so the part is less model-specific than the opener itself. The real question is which generation of keypad you have. Older units use a screw-terminal wiring block; newer ones use a plug-in connector with a different post spacing. If you order the wrong one, the plug won’t seat and the keypad won’t power up.
Before we quote anything, we look at three things: the label inside the opener control box, the model number on the back of the keypad or intercom faceplate, and the actual wire gauge running from the gate post to wherever the keypad is mounted. Ghost Controls wiring typically runs low-voltage and the spec matters. If a previous owner ran the wrong gauge or spliced it mid-run, the keypad can test fine on the bench and still fail in the yard.
On OEM versus aftermarket: for a Ghost Controls keypad, we generally recommend the factory-matching part because the connector and programming sequence match what’s documented for your unit. Aftermarket keypads work, but they require re-pairing the remotes and often don’t hold up through Nevada’s summer heat. We don’t stock parts or carry them on a truck. We source them per job, which is why the quote reflects the exact part you need, and we’ll tell you plainly if the aftermarket equivalent is a square deal for your situation. Ironworks Gate Co. Winchester is an independent service provider and not affiliated with Ghost Controls.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Keypad & Intercom Repair Is Failing
- You have to press a code two or three times. The membrane switch behind the buttons wears out. On a gate post in full afternoon sun, that membrane can go soft in five or six years in this climate.
- The keypad lights flicker or go dark entirely. Usually a failing wire connection at the gate post, not the keypad. The screw terminal loosens from gate vibration, or the low-voltage run has corroded at the splice.
- The intercom sounds crackly or cuts in and out. Moisture working into the handset or speaker grille. Winchester’s spring dust and summer monsoon humidity both find their way into that housing.
- The gate opens on the remote but not the keypad. The opener is fine. The problem is the keypad, the wire run to it, or the programming has reset. If it resets after every power blip, the backup battery in the keypad may be spent.
- The intercom buzzer rings but no voice comes through. Partial failure in the intercom module. Often one channel or one direction dies before the whole unit does.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
| Item | Typical installed range |
|---|---|
| Keypad replacement, standard model | $185 – $240 |
| Intercom module replacement | $240 – $340 |
| Wire run repair or re-termination | $120 – $220 |
| Keypad and intercom together | $320 – $460 |
What drives the range: the specific keypad or intercom model, whether the existing wire is reusable, and whether the gate post needs any mounting work. Parts and labor are quoted separately and clearly. We settle the price with you before a bolt is turned, so the bill matches the quote. Every job comes with our written 90-Day Done Right Promise: if something isn’t right, we come back and fix it.
DIY or Call Us?
Safe to check yourself: whether the keypad has power (many have a small LED), whether the code works from a second keypad if you have one, and whether the wire at the gate post is visibly loose or corroded. Those are worth a look.
Where it goes wrong: cracking open the opener control box to test low-voltage terminals while the gate is live, or running new wire from the house to the gate. That control box holds a low-voltage system, but the opener is powered by line voltage, and a gate that moves without warning is a real hazard. Testing the wrong terminal while a motor can start is not worth saving a service call. For anything past the faceplate, call us at (866) 984-8340. We’ll tell you honestly if it’s a simple re-termination or a full replacement.
FAQs
Expect six to ten years for a keypad and five to eight for an intercom in this climate. Full sun on a west-facing gate post and the dust that settles into the buttons both shorten that. Units under a shaded post or covered entry tend to last toward the longer end.
Sometimes. A loose terminal or a bad splice is a repair, often $120 to $220. Once the membrane inside the keypad or the speaker in the intercom goes, replacement is the honest answer, and we’ll say so rather than charge you twice.
Most keypad and intercom replacements take one to two hours on site, and most jobs are completed in a single visit. If the wire run needs replacing, add another hour or so. We quote the whole job up front so there are no surprises.
We order the part matched to your exact Ghost Controls model after we’ve confirmed compatibility on site. That means the quote reflects the right part, not a guess. It also means the part is ordered for your job, not pulled from a shelf.
Call (866) 984-8340 for a free estimate. Our technicians have up to 13 years of experience, we answer the phone 24 hours a day, and every job is backed by the 90-Day Done Right Promise. We also currently offer $50 Off Any Repair Over $250 and a free second opinion on any written estimate.
Written by the team at Ironworks Gate Co. Winchester, serving Winchester and nearby areas.