A Ironworks company - serving Winchester, NV

Ghost Controls Welding & Fabrication in Winchester, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Welding & Fabrication: The Winchester Owner’s Guide

We repair and fabricate the welded steel components on Ghost Controls gate systems in Winchester, and most bracket, arm, and hinge weld jobs land between $240 and $520 installed depending on how much metal has to be cut out and rebuilt. We schedule these as measured jobs rather than same-day dispatches, because the correct fix depends on what we find once the arm is off and the post is exposed. Call (866) 984-8340 and we’ll set a free measure and hand you a written price before anything is ordered.

Call (866) 984-8340

Owners in Winchester usually find this problem the same way: the gate starts dragging at one end of its travel, the opener motor strains or trips its breaker, and a look at the mounting bracket shows a weld cracked clean through or a plate rusted paper-thin at the toe. On older installations, the actuator arm bracket separates from the gate frame where the two dissimilar metals meet. That’s a welding and fabrication job, not a parts swap, and it’s the one most generalists won’t touch.

Which Ghost Controls Models This Applies To

Ghost Controls builds its residential line around the AXS, TDS, and ZDS series, with the heavier-duty models using thicker-walled mounting arms and a wider post bracket than the lighter kits. The welded parts we fabricate most often are the gate-side mounting bracket, the operator post plate, and the arm-to-gate connection on double-swing setups. The first thing to check is the data label on the control box door: the model number tells you the arm geometry, and the arm geometry tells you what bracket the gate frame has to accept. Guessing here is how a gate ends up binding halfway open.

On the OEM-versus-aftermarket question, our honest answer for Ghost Controls specifically is that the factory brackets and arms are the right starting point when the original is still serviceable enough to match dimensions. Where the factory bracket has rusted out or the gate frame has settled since it was hung, a fabricated replacement built to the actual gate in front of us is the stronger fix, because a stamped bracket can only fit a gate that’s still square. We fabricate to the gate, not to a spec sheet. We’re an independent service provider and not affiliated with Ghost Controls, so we have no interest in steering you toward a brand name over a part that fits.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Ghost Controls Welding & Fabrication Is Failing

  • The gate drags at one end of its travel. A cracked bracket weld lets the arm shift under load, so the gate binds near open or near close while running freely in between. The travel itself gives the diagnosis away.
  • Rust bleeding from a weld seam. Southern Nevada’s dry air hides corrosion until it doesn’t. Monsoon-season moisture sitting in a weld toe on a north-facing post is what eats the metal from the inside out.
  • Visible hairline crack at the bracket-to-frame joint. Look close with a flashlight where the bracket meets the gate tube. A crack that opens when the gate moves is a fatigue crack, and it will not heal itself.
  • The opener motor strains or trips its breaker mid-cycle. When the binder is mechanical and the operator keeps pushing, the motor and control board take the punishment. That’s how a $300 weld job becomes a motor repair.
  • The arm wobbles at its mounting point. A loose arm pivot means the bolt hole has wallowed out or the plate has fatigued. Retorquing the bolt only buys a few weeks before the hole is oversized and the plate has to be replaced.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

In Winchester, expect $240 to $340 for a straightforward bracket re-weld and re-hang, and $380 to $520 when the job means cutting out fatigued metal and fabricating a new plate or arm connection, then refinishing the weld. What drives the range is access, how much original metal is sound enough to weld to, whether the gate has to come off its hinges, and the finish work. Here’s what the price covers:

  • Parts and fabrication: steel plate, tube, or bracket stock, cut and fit to your gate.
  • Labor: removal, welding, alignment, and re-hanging so the gate swings true.
  • Finish: primer and paint or cold galvanizing on the repaired area.
  • Operator check: we run the Ghost Controls arm through a full open and close cycle and confirm limit positions hold after the weld cools.
  • Workmanship warranty: our welds are covered, and every job carries the 90-Day Done Right Promise in writing if anything we touched isn’t right.

The price is quoted and agreed before a single bolt is turned. You will not get an invoice larger than the number you approved.

DIY or Call Us?

There are two things you can safely check yourself: with the opener powered off at the breaker, walk the gate through its full swing by hand and feel where it binds, and look at the bracket-to-frame joint with a flashlight for cracks or rust staining. Write down what you find. That’s the extent of it.

Where DIY goes wrong is the welding itself. Gate frames carry the full weight of the gate and the thrust of the operator, and a weld that looks solid but lacks penetration will fail under load, sometimes with the gate coming down. The arm is also under spring or operator tension and can move suddenly the moment a bracket lets go. Arc welding near a gate also means hot slag, a live electrical circuit, and a fire risk in dry brush. This is a job for a trained welder who can also confirm the operator still limits correctly after the steel is repaired. Call (866) 984-8340 and we’ll schedule a free measure and give you a written price.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 60-minute response · free estimates
Call (866) 984-8340
Local Service Coverage

Request a Free Estimate in Winchester

Tell us what you need - Ironworks Gate Co. Winchester responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch