Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Motor Replacement: The Winchester Owner’s Guide
We replace failed Ghost Controls gate motors for Winchester homeowners, and a typical installed replacement runs $520 to $980 depending on the model, gate weight, and whether the control board or just the motor head is being swapped. Same-day service is often available for a dead arm on a single-swing driveway gate. Most owners find out the motor is going when the gate stop-and-reverses halfway through its travel, when they hear a grinding groan from the housing on a hot afternoon, or when the arm runs but the gate barely moves.
Key Takeaways
- We service all common Ghost Controls arm and operator models found on Winchester driveway gates.
- Installed replacement pricing sits between $520 and $980, quoted and agreed before any work starts.
- Summer heat in Winchester is hard on motor windings and control boards – the two parts that fail most.
- Every replacement is backed by our written 90-Day Done Right Promise.
Which Ghost Controls Models This Applies To
Ghost Controls builds a small family of residential arm operators – the single-swing and dual-swing arms most Winchester homeowners have, plus the heavy-duty arms for wider and solid gates. The quickest way to identify yours is the data plate on the underside of the motor housing or the label inside the control box lid. If the plate is sun-bleached and unreadable (common after a few Las Vegas Valley summers), measure the gate leaf width and its weight, note the arm’s extended and retracted length, and we’ll match it. We carry no parts on a truck and stock nothing locally, so we order the correct replacement head for your specific model once we’ve confirmed the fit.
On the OEM-vs-aftermarket call: for Ghost Controls specifically, we recommend the genuine replacement arm or control board in most cases, because the internal gearing and the board’s firmware are matched to the model. A generic aftermarket arm may physically bolt on but will often trip the gate’s obstruction sensing early or run at the wrong speed. We’ll tell you honestly when a quality aftermarket equivalent is a safe swap and when it isn’t. Ironworks Gate Co. Winchester is an independent service provider and is not affiliated with Ghost Controls. We also service LiftMaster, Mighty Mule, DoorKing, and six other automation brands when your gate is on a different system.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Gate Motor Replacement Is Failing
Most Ghost Controls motor failures in Winchester announce themselves well before the gate stops moving entirely. Here’s what we hear from owners, and what each symptom usually means under the housing:
- The gate reverses on its own partway through travel. The obstruction sensing is tripping. Often a worn arm or a binding hinge is loading the motor past its limit, and the board shuts it down to protect itself. Left alone, the windings overheat and the arm fails outright.
- A grinding or growling noise from the arm. The internal gear train is worn. Ghost Controls arms use a plastic-and-metal reduction gear, and the plastic side strips first. Once it starts grinding, the arm is on borrowed time.
- The arm runs but the gate doesn’t move, or moves slowly. The motor is spinning but the output is slipping – usually a stripped gear or a failing clutch. This is the classic end-stage symptom.
- The gate won’t respond to the remote or keypad, but the arm hums. The control board has failed, not the motor. In Winchester heat, board failures from voltage spikes and thermal cycling are common. A board swap is cheaper than a full arm replacement.
- Erratic limit stops – the gate over-travels or stops short. The limit switches or their magnets have drifted. Sometimes this is a reset; sometimes the sensor board inside the arm has failed.
One safety note before you start poking around: the arm operator itself is lower voltage and not the hazard some gate parts are, but a gate that reverses unpredictably can crush or trap – a person, a pet, a vehicle. If your gate is misbehaving, keep it in manual release until we’ve looked at it. The arm’s battery-backed control box also holds a live battery, so don’t open the lid and start unplugging things if you’re not sure what you’re looking at.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s how the pricing breaks down for a Ghost Controls motor replacement in Winchester. These are installed ranges – parts plus labor – and the price is quoted and agreed before a single bolt is turned:
| What’s being replaced | Typical installed range |
|---|---|
| Control board only (motor and arm are fine) | $320 – $480 |
| Single-swing arm/motor head replacement | $520 – $780 |
| Dual-swing (two arms) replacement | $980 – $1,540 |
| Heavy-duty arm for a wide or solid gate | $720 – $1,050 |
What drives the range: the model of arm, the weight and width of your gate leaf, whether the control board is also being replaced, and whether the gate’s hinges or stops need attention while we’re in there. A gate that binds will kill a fresh motor faster than anything, so we correct that rather than sell you a new arm into the same problem. Every replacement is backed by our written 90-Day Done Right Promise – if it’s not right, we come back and make it right, no arguing.
DIY or Call Us?
There’s a fair amount a homeowner can safely check. You can confirm the gate moves freely by hand in manual release, look for a binding hinge or a leaf dragging on the ground, check that the arm’s mounting brackets are tight, and swap the batteries in your remote and keypad. Those cover a surprising share of “dead motor” calls.
Where DIY goes wrong on this part: diagnosing whether the fault is the board, the arm, or the gate itself takes a meter and experience, and homeowners routinely buy an arm they didn’t need or replace an arm into a gate that was binding and kills the new one within weeks. If the gate reverses unpredictably, that’s a safety condition – don’t test it by walking your gate through its cycle. Call us at (866) 984-8340 and we’ll sort out what’s actually failed.
FAQs
A residential Ghost Controls arm typically lasts 8 to 12 years with normal use and upkeep. In Winchester, expect the lower end of that if your gate gets daily sun exposure and the housing heats up – the motor windings and control board take the worst of it. Keeping the gate’s hinges lubed and the arm’s mounts tight extends the life more than anything else.
Sometimes, yes. A failed control board can often be swapped on its own without replacing the arm, and that’s the cheaper fix when the motor and gearing are still sound. A stripped gear or a burned-out motor means the arm gets replaced. We’ll tell you which it is before we quote, so you’re not paying for an arm you don’t need. Call (866) 984-8340 for a free estimate.
A single-swing arm replacement usually takes one to two hours once the correct part is on hand. Because we don’t stock parts locally, the timeline depends on sourcing the right replacement head – most jobs are completed in a single visit after the part arrives. Dual-swing and heavy-duty arms take longer.
We order the correct Ghost Controls replacement head or board for your specific model once we’ve confirmed the fit from the data plate or measured the gate. We use genuine parts in most cases, since the gearing and firmware are matched to the model, and we’ll tell you when a quality aftermarket equivalent is a safe substitute. Call (866) 984-8340 for a free estimate on your Winchester gate.
We’d rather get your Ghost Controls gate closing right the first time than sell you a part you don’t need. When the arm is failing, call us at (866) 984-8340 for a free estimate – we’ll identify the actual fault, quote the exact price before we start, and stand behind the work with our written 90-Day Done Right Promise. We’re your Winchester gate specialist, and we serve homeowners here the same way we’d serve our own family.
Written by the team at Ironworks Gate Co. Winchester, serving Winchester and nearby areas.