Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Motor & Opener in Winchester: What to Know First
We service and repair Ghost Controls gate motors and openers in Winchester as an independent Ghost Controls service provider, and most single-operator residential jobs are diagnosed and completed in one visit. Prices are agreed with you before we turn a single bolt, and every completed job is backed by our written 90-Day Done Right Promise. If your gate has stopped, is running slow, or is beeping at you from the control box, call (866) 984-8340 and a live person will answer, day or night.
This page is for Winchester homeowners who already own a Ghost Controls system and want it fixed correctly, not replaced with whatever a salesman is pushing that week. We work on Ghost Controls units across the valley, from the newer homes off Horizon Ridge to the established properties near the Winchester Park area, and we know exactly what tends to go wrong on each series.
How Ghost Controls Products Fail – and How We Fix Them
Ghost Controls makes a genuinely good residential automatic gate opener. The company builds solar-friendly, low-voltage operators that suit single-driveway gates, and that is what most Winchester homeowners have. The failures are predictable once you have worked on enough of them. Here are the ones we see most often.
- Battery and solar charge failures on the TSS1 and AXS1 series. The control board reads a low battery and either refuses to run the gate or runs it slowly and erratically. Most owners assume the motor has died; usually the problem is the battery itself, a loose solar panel connection, or a charge controller that has stopped feeding the battery properly. We test the battery under load and check the panel output before recommending a replacement.
- Arm and limit-switch wear on the single-arm units. The gate drifts past its stop point or reverses at random. On the tube-arm and single-arm designs, the limit switches and the arm pivot hardware wear over time, especially on older iron gates that have gained a little sag. We realign the arm geometry and reset the limits rather than just swapping parts.
- Control board and receiver faults after a summer of heat. Winchester summers are hard on any outdoor electronics, and Ghost Controls control boards are no exception. A board that has cooked in a metal enclosure can lose its radio receiver, forget its limits, or refuse to accept a remote. We confirm it is the board and not the wiring before replacing it, because a bad ground or a chewed wire looks exactly like a dead receiver from the outside.
- Entrapment and safety-sensor nuisance trips. The gate stops and reverses halfway, or will not close at all. More often than not this is a misaligned or dirty safety sensor, a loose connection at the operator, or a photo-eye knocked out of position. We realign and test the full safety circuit, which is the part that matters most on a residential driveway.
- Obstruction-sensing calibration drift. The gate meets a little resistance and gives up. Ghost Controls units are set to sense obstruction for safety, but when the gate hardware tightens up or the hinges dry out, that sensitivity trips too early. We free up and service the gate hardware first, then recalibrate the operator to match the gate as it actually runs.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Ghost Controls Gate Motor & Opener Process
We keep the job simple and we keep you informed at each step. Here is what a Ghost Controls service call looks like from the first ring to the final walk-around.
- 1
You call and a live person answers. We take your details and the symptom over the phone, whether it is two in the afternoon or two in the morning, so we arrive already knowing what to expect.
- 2
We diagnose on site. We test the battery, the solar input if you have one, the control board, the limits, and the safety circuit in a set order. We do not guess and we do not replace parts to see if the guess was right.
- 3
We give you a written price before we start. You see the parts and labor and you approve it before we touch anything. No surprises on the bill.
- 4
We make the parts call honestly. Sometimes a genuine Ghost Controls part is the right answer for a warranty-safe repair; sometimes a quality aftermarket battery or sensor is the smarter, longer-lasting choice. We tell you which and why.
- 5
We do the repair and test the whole gate. Not just the operator: the hinges, the latches, the safety edges, and the full open-and-close cycle, several times, until it runs clean.
- 6
We clean up and back it in writing. The 90-Day Done Right Promise is on the job. If it is not right, we come back and make it right.
See the difference
Before
After
Before
After
Before
AfterWhat Ghost Controls Gate Motor & Opener Costs in Winchester
Prices vary with the symptom and the parts needed, but here is the honest range for the most common Ghost Controls jobs we handle in Winchester. Every price is quoted and agreed before any work starts, and the estimate is free.
| Job | Typical range |
|---|---|
| Diagnostic and tune-up | $89 seasonal tune-up (standing offer) |
| Battery or solar charge repair | $150 – $320 |
| Safety sensor / entrapment circuit repair | $140 – $280 |
| Control board or receiver replacement | $280 – $520 |
| Arm, limit, and hardware realignment | $180 – $360 |
| Full motor replacement (single operator) | $650 – $1,200 installed |
Parts, labor, and the condition of the gate all move the number. A gate that swings free is cheaper to fix than one that is dragging on its hinges. We give you the price before we start. Call (866) 984-8340 for your free estimate, and remember the $50 off any repair over $250 and the free second opinion on any written estimate.
Why Winchester Homeowners Call Ironworks Gate Co. Winchester for Ghost Controls Work
We have been doing this work in the community for over 42 years, and we plan to be here for another forty. That is why we stand behind every job with a written guarantee instead of a handshake and a hope. Our technicians have up to 13 years of experience, they are background-checked and uniformed, and they treat your property the way they would their own. They are trained and equipped on nine gate-automation brands, so if your Ghost Controls unit turns out to be beyond repair, we can recommend and install the right replacement, whether that is Ghost Controls, LiftMaster, Mighty Mule, or DoorKing, without steering you toward whatever we happen to have on hand. A live person answers the phone 24 hours a day, and the price you agree to is the price you pay.
FAQs
No. Our repairs are done to keep your manufacturer warranty intact, and where an OEM part is required we use it. As an independent Ghost Controls service provider we are not affiliated with or authorized by Ghost Controls, but we know what their warranty expects and we work within it. Call (866) 984-8340 with your model number and we will tell you exactly where you stand.
Yes. We source genuine Ghost Controls parts and quality aftermarket equivalents, so the right part is on the job when we need it. That is one reason most Ghost Controls jobs are finished in a single visit. Call (866) 984-8340 for a free estimate.
Repair it if the motor and board are sound and the failure is a battery, sensor, limit, or arm problem, which is most of the time. Replace it only when the board and motor are both failing or the unit is simply past its service life. We will tell you honestly which you are looking at. Call (866) 984-8340 and we will give you a straight answer.
We aim to complete most Ghost Controls jobs in a single visit, and live phone support is available 24 hours a day, 7 days a week. Call (866) 984-8340 and we will schedule you in.
Yes. We are trained and equipped on nine brands, including LiftMaster, Mighty Mule, and DoorKing, so we are not limited to Ghost Controls. Whatever is on your driveway, we can service it. Call (866) 984-8340 for a free estimate.
It covers the work we did: if it is not right, we come back and make it right, with no paperwork and no arguing, for 90 days after the job. That is the Keystone Standard, and it applies to every Ghost Controls job in Winchester. Call (866) 984-8340 to book yours.
Written by the team at Ironworks Gate Co. Winchester, serving Winchester and nearby areas.
Ready to get your Ghost Controls gate running right? Call (866) 984-8340 for a free estimate. A live person answers, day or night, and the price is agreed before we start.